Examinando por Materia "Tensile mechanical stress"
Mostrando 1 - 3 de 3
Resultados por página
Opciones de ordenación
Ítem Water-based adhesive formulations for rubber to metal bonding developed by statistical design of experiments(Elsevier Ltd, 2017-03-01) Lasprilla-Botero, J.; Álvarez-Láinez, M.; Acosta, D.A.; Lasprilla-Botero, J.; Álvarez-Láinez, M.; Acosta, D.A.; Universidad EAFIT. Departamento de Ingeniería de Procesos; Procesos Ambientales (GIPAB)Waterborne adhesives for rubber to metal bonding have been available since 1990. However, published information about their formulation has been limited, as proprietary restrictions are exercised by companies. As a consequence, the way these adhesives interact with substrates has not been studied extensively. With the aim of investigating the effect the components of a waterborne adhesive have on rubber to metal bonding, fractional factorial and surface response methodologies of design of experiments were employed in this study. Twenty six formulations were prepared with a polychloroprene latex as the adhesive polymer. Viscosity, wettability and non-volatile solids content were measured with each liquid adhesive, while the mechanical strength was evaluated by applying a tensile mechanical stress over cured solid adhesive films. Adhesion properties were evaluated by using a single lap-shear test on metal to metal joints and a pull-out test on rubber to metal joints. The results showed that the components with the largest relative influence on cohesive and adhesives forces were tackifier resin, silicon dioxide and polychloroprene latex type. In order to better understand the contributions of these variables, mathematical models correlating them with the response variables were obtained. This study is valuable in explaining how, through statistical methods, a waterborne adhesive for rubber to metal bonding can be formulated with a reasonably low number of experiments. © 2016 Elsevier LtdÍtem Water-based adhesive formulations for rubber to metal bonding developed by statistical design of experiments(Elsevier Ltd, 2017-03-01) Lasprilla-Botero, J.; Álvarez-Láinez, M.; Acosta, D.A.; Universidad EAFIT. Departamento de Ingeniería de Diseño; Ingeniería de Diseño (GRID)Waterborne adhesives for rubber to metal bonding have been available since 1990. However, published information about their formulation has been limited, as proprietary restrictions are exercised by companies. As a consequence, the way these adhesives interact with substrates has not been studied extensively. With the aim of investigating the effect the components of a waterborne adhesive have on rubber to metal bonding, fractional factorial and surface response methodologies of design of experiments were employed in this study. Twenty six formulations were prepared with a polychloroprene latex as the adhesive polymer. Viscosity, wettability and non-volatile solids content were measured with each liquid adhesive, while the mechanical strength was evaluated by applying a tensile mechanical stress over cured solid adhesive films. Adhesion properties were evaluated by using a single lap-shear test on metal to metal joints and a pull-out test on rubber to metal joints. The results showed that the components with the largest relative influence on cohesive and adhesives forces were tackifier resin, silicon dioxide and polychloroprene latex type. In order to better understand the contributions of these variables, mathematical models correlating them with the response variables were obtained. This study is valuable in explaining how, through statistical methods, a waterborne adhesive for rubber to metal bonding can be formulated with a reasonably low number of experiments. © 2016 Elsevier LtdÍtem Water-based adhesive formulations for rubber to metal bonding developed by statistical design of experiments(Elsevier Ltd, 2017-03-01) Lasprilla-Botero, J.; Álvarez-Láinez, M.; Acosta, D.A.; Universidad EAFIT. Departamento de Ingeniería de Procesos; Desarrollo y Diseño de ProcesosWaterborne adhesives for rubber to metal bonding have been available since 1990. However, published information about their formulation has been limited, as proprietary restrictions are exercised by companies. As a consequence, the way these adhesives interact with substrates has not been studied extensively. With the aim of investigating the effect the components of a waterborne adhesive have on rubber to metal bonding, fractional factorial and surface response methodologies of design of experiments were employed in this study. Twenty six formulations were prepared with a polychloroprene latex as the adhesive polymer. Viscosity, wettability and non-volatile solids content were measured with each liquid adhesive, while the mechanical strength was evaluated by applying a tensile mechanical stress over cured solid adhesive films. Adhesion properties were evaluated by using a single lap-shear test on metal to metal joints and a pull-out test on rubber to metal joints. The results showed that the components with the largest relative influence on cohesive and adhesives forces were tackifier resin, silicon dioxide and polychloroprene latex type. In order to better understand the contributions of these variables, mathematical models correlating them with the response variables were obtained. This study is valuable in explaining how, through statistical methods, a waterborne adhesive for rubber to metal bonding can be formulated with a reasonably low number of experiments. © 2016 Elsevier Ltd