Examinando por Materia "Biochemical oxygen demand"

Mostrando 1 - 4 de 4
  • No hay miniatura disponible
    Ítem
    Mineralization of cyanide originating from gold leaching effluent using electro-oxidation: multi-objective optimization and kinetic study
    (SPRINGER, 2020-01-01) Dobrosz-Gómez I.; Gómez García M.Á.; Gaviria G.H.; GilPavas E.; Universidad EAFIT. Departamento de Ingeniería de Procesos; Desarrollo y Diseño de Procesos
    Abstract: This study examines the electro-oxidation (EO) of cyanide originating from an industrial plant´s gold leaching effluent. Experiments were carried out in a laboratory-scale batch cell reactor. Monopolar configuration of electrodes consisting of graphite (anode) and aluminum (cathode) was employed, operating in galvanostatic mode. Response Surface Methodology (RSM), based on a Box–Behnken experimental Design (BBD), was used to optimize the EO operational conditions. Three independent process variables were considered: initial cyanide concentration ([CN-]0 = 1000–2000 mg L-1), current density (J =7–107 mA cm-2), and stirring velocity (? = 250–750 rpm). The cyanide conversion (XCN-), Chemical Oxygen Demand (COD) removal percentage (%RCOD), and specific Energy Consumption per unit mass of removed cyanide (EC) were analyzed as response variables. Multi-objective optimization let to establish the most effective EO conditions ([CN-]0 = 1000 mg L-1, J = 100 mA cm-2 and ? = 750 rpm). The experimental data (XCN-, %RCOD, and EC) were fitted to second-order polynomial models with adjusted correlation coefficients (Radj2) of ca. 98, 99 and 87%, respectively. The kinetic analysis, performed at optimal EO operational conditions, allowed determination of time required to meet Colombian permissible discharge limits. The predictive capacity of kinetic expressions was verified against experimental data obtained for gold leaching effluent. Total cyanide removal and 96% of COD reduction were obtained, requiring EC of 71.33 kWh kg-1 and 180 min. The BOD5 (biological oxygen demand)/COD ratio increased from 4.52 × 10-4 to 0.5573, confirming effluent biodegradability after EO treatment. Graphic Abstract: [Figure not available: see fulltext.]The variation of cyanide (CN-), cyanate (CNO-) and ammonium (NH4 +) ions concentrations vs. time at alkaline conditions. EO operational conditions: [CN-]0 = 1000 mg/L, J = 100 mA/cm2 , ? = 750 rpm, [NaCl] = 0.15 M and pH 11.1. © 2020, Springer Nature B.V.
  • No hay miniatura disponible
    Ítem
    Mineralization of cyanide originating from gold leaching effluent using electro-oxidation: multi-objective optimization and kinetic study
    (SPRINGER, 2020-01-01) Dobrosz-Gómez I.; Gómez García M.Á.; Gaviria G.H.; GilPavas E.; Dobrosz-Gómez I.; Gómez García M.Á.; Gaviria G.H.; GilPavas E.; Universidad EAFIT. Departamento de Ingeniería de Procesos; Procesos Ambientales (GIPAB)
    Abstract: This study examines the electro-oxidation (EO) of cyanide originating from an industrial plant´s gold leaching effluent. Experiments were carried out in a laboratory-scale batch cell reactor. Monopolar configuration of electrodes consisting of graphite (anode) and aluminum (cathode) was employed, operating in galvanostatic mode. Response Surface Methodology (RSM), based on a Box–Behnken experimental Design (BBD), was used to optimize the EO operational conditions. Three independent process variables were considered: initial cyanide concentration ([CN-]0 = 1000–2000 mg L-1), current density (J =7–107 mA cm-2), and stirring velocity (? = 250–750 rpm). The cyanide conversion (XCN-), Chemical Oxygen Demand (COD) removal percentage (%RCOD), and specific Energy Consumption per unit mass of removed cyanide (EC) were analyzed as response variables. Multi-objective optimization let to establish the most effective EO conditions ([CN-]0 = 1000 mg L-1, J = 100 mA cm-2 and ? = 750 rpm). The experimental data (XCN-, %RCOD, and EC) were fitted to second-order polynomial models with adjusted correlation coefficients (Radj2) of ca. 98, 99 and 87%, respectively. The kinetic analysis, performed at optimal EO operational conditions, allowed determination of time required to meet Colombian permissible discharge limits. The predictive capacity of kinetic expressions was verified against experimental data obtained for gold leaching effluent. Total cyanide removal and 96% of COD reduction were obtained, requiring EC of 71.33 kWh kg-1 and 180 min. The BOD5 (biological oxygen demand)/COD ratio increased from 4.52 × 10-4 to 0.5573, confirming effluent biodegradability after EO treatment. Graphic Abstract: [Figure not available: see fulltext.]The variation of cyanide (CN-), cyanate (CNO-) and ammonium (NH4 +) ions concentrations vs. time at alkaline conditions. EO operational conditions: [CN-]0 = 1000 mg/L, J = 100 mA/cm2 , ? = 750 rpm, [NaCl] = 0.15 M and pH 11.1. © 2020, Springer Nature B.V.
  • No hay miniatura disponible
    Ítem
    The removal of the trivalent chromium from the leather tannery wastewater: the optimisation of the electro-coagulation process parameters.
    (IWA PUBLISHING, 2011-02-01) GilPavas, E.; Dobrosz-Gomez, I.; Gomez-Garcia, M. A.; GilPavas, E.; Dobrosz-Gomez, I.; Gomez-Garcia, M. A.; Universidad EAFIT. Departamento de Ingeniería de Procesos; Procesos Ambientales (GIPAB)
    The capacity of the electro-coagulation (EC) process for the treatment of the wastewater containing Cr3+, resulting from a leather tannery industry placed in Medellin (Colombia), was evaluated. In order to assess the effect of some parameters, such as: the electrode type (Al and/or Fe), the distance between electrodes, the current density, the stirring velocity, and the initial Cr3+ concentration on its efficiency of removal (%RCr+3), a multifactorial experimental design was used. The %RCr3+ was defined as the response variable for the statistical analysis. In order to optimise the operational values for the chosen parameters, the response surface method (RSM) was applied. Additionally, the Biological Oxygen Demand (BOD5), the Chemical Oxygen Demand (COD), and the Total Organic Carbon (TOC) were monitored during the EC process. The electrodes made of aluminium appeared to be the most effective in the chromium removal from the wastewater under study. At pH equal to 4.52 and at 28 degrees C, the optimal conditions of Cr3+ removal using the EC process were found, as follows: the initial Cr3+ concentration=3,596 mg/L, the electrode gap=0.5 cm, the stirring velocity=382.3 rpm, and the current density=57.87 mA/cm2. At those conditions, it was possible to reach 99.76% of Cr3+ removal, and 64% and 61% of mineralisation (TOC) and COD removal, respectively. A kinetic analysis was performed in order to verify the response capacity of the EC process at optimised parameter values.
  • No hay miniatura disponible
    Ítem
    Treatment of automotive industry oily wastewater by electrocoagulation: statistical optimization of the operational parameters.
    (IWA PUBLISHING, 2009-11-01) GilPavas, Edison; Molina-Tirado, Kevin; Angel Gomez-Garcia, Miguel; GilPavas, Edison; Molina-Tirado, Kevin; Angel Gomez-Garcia, Miguel; Universidad EAFIT. Departamento de Ingeniería de Procesos; Procesos Ambientales (GIPAB)
    An electrocoagulation process was used for the treatment of oily wastewater generated from an automotive industry in Medellin (Colombia). An electrochemical cell consisting of four parallel electrodes (Fe and Al) in bipolar configuration was implemented. A multifactorial experimental design was used for evaluating the influence of several parameters including: type and arrangement of electrodes, pH, and current density. Oil and grease removal was defined as the response variable for the statistical analysis. Additionally, the BOD(5), COD, and TOC were monitored during the treatment process. According to the results, at the optimum parameter values (current density = 4.3 mA/cm(2), distance between electrodes = 1.5 cm, Fe as anode, and pH = 12) it was possible to reach a c.a. 95% oils removal, COD and mineralization of 87.4% and 70.6%, respectively. A final biodegradability (BOD(5)/COD) of 0.54 was reached.